in reply to Cisco Telnet

No need to slurp the seed file, you can iterate over the lines. Make it a habit to use the three-argument form of open. As a rule of thumb, using lexical variables for you filehandles is better. 
use strict;
use Net::Telnet::Cisco;

open my $log, '>', 'mylogfilepath'
    or die "Cannot writeopen log file: $!\n";

open my $seed, '<', 'myseedfilepath'
    or die "Cannot readopen seed file: $!\n";

while(<$seed>) {
    chomp;
    my $Telnet = Net::Telnet::Cisco->new(Host => $_);
    $Telnet->login(Name => 'user', Password => 'pass');

    print $log "$ip\n", map $Telnet->cmd($_), 'show line 1', 'show lin
+e 5';
}

[download]

Makeshifts last the longest.

Replies are listed 'Best First'.
Re: Re: Cisco Telnet
by CongoGrey (Sexton) on Feb 19, 2003 at 14:37 UTC
    Thanks for the input...but, I am not able to get the script to run properly I got this far: 
    use strict;
use Net::Telnet::Cisco;

open my $log, '>', 'logfilepath' or die "Cannnot open log file : $!\n"
+;

open my $seed, '+<', 'seedfilepath' or die "Cannot open file : $!\n";

while($seed) {
    chomp $seed;
    my $Telnet = Net::Telnet::Cisco->new(Host => $_ or die "Cannot ope
+n session to '$seed': $!\n");
    $Telnet->login(Name => 'rschuman', Password => 'tagheuer1') or die
+ "Cannot log into device '$_': $!\n";
    print $log "$_\n", map $Telnet->cmd($_), 'show line aux 0';    
}

    [download]
    I get the following error: Useless use of a constant in void context at C:\Documents and Settings\rschuman\ Desktop\telnet2.pl line 24. Cannot open session to 'GLOB(0x1abf15c)': I also realized that the original script's output was to much so i added a grep of the output: 
    use strict;
use Net::Telnet::Cisco;
#
open (LOGFILE, '>logfilepath') or die "Cannnot open log file : $!\n";
#
open (SEEDFILE, 'seedfilepath') or die "Cannot open file : $!\n";

my @iplist = <SEEDFILE>;
foreach my $ip (@iplist) {
    select LOGFILE;
    print "$ip\n";
    my $Telnet = Net::Telnet::Cisco->new(Host => $ip) or die "Cannot o
+pen session to '$ip': $!\n";
    $Telnet->login(Name => 'user', Password => 'pass') or die "Cannot 
+log into device '$ip': $!\n";
    my $output = $Telnet->cmd('show line aux 0');
    my $matchlines = grep (/Modem hardware state:/,  $output);
    print "$matchlines\n";
}

close LOGFILE;
close SEEDFILE;

    [download]
    I also get the following error even though the script does run: Argument "" isn't numeric in numeric gt (>) at C:/Perl/site/lib/Net/Telnet.pm li ne 2569, <SEEDFILE> line 3.
[reply]
[d/l]
[select]
      In the first script you forgot to actually use the filehandle to read from it: it must be while(<$seed>) - note the angle brackets. Also, you misplaced a paren two lines later - it must be 
      my $Telnet = Net::Telnet::Cisco->new(Host => $_)
    or die "Cannot open session to '$seed': $!\n";

      [download]

      Makeshifts last the longest.

[reply]
[d/l]
[select]
        Aristotle, I appreciate you help on this and i want to have as clean a script a possible. Here is my latest version: 
        use strict;
use Net::Telnet::Cisco;
open my $log, '>', 'logfile' or die "Cannnot open log file : $!\n";
open my $seed, '<', 'seedfile' or die "Cannot open seed file : $!\n";

while(<$seed>) {
    chomp;
    my $Telnet = Net::Telnet::Cisco->new(Host => $_) or die "Cannot op
+en session to '$seed': $!\n";
    $Telnet->login(Name => 'user', Password => 'pass') or die "Cannot 
+log into device '$_': $!\n";
    print $log "$_\n", map $Telnet->cmd($_), 'show line aux 0';    
}

        [download]
        I get the following error: Argument "" isn't numeric in numeric gt (>) at C:/Perl/site/lib/Net/Telnet.pm li ne 2569, <$seed> line 1. Modification of a read-only value attempted at C:/Perl/site/lib/Net/Telnet/Cisco .pm line 751, <$seed> line 1. I can't seem to figure out where Perl thinks i am trying to modify the varible from the filehandle.
[reply]
[d/l]

In Section Code Catacombs