You're correct. Your example gives perl the code ; to execute (i.e. an empty statement; personally I tend to use -e 0 since it accomplishes the same thing and doesn't require quoting to prevent it from being interpreted by the shell). If nothing happens that's good, as it means that the CGI module was found and loaded correctly. Had it not found the module or something blew up you would have instead seen an error (and you could experimentally verify this by trying to load a non-existent module, e.g. perl -MThroatwarbler::Mangrove -e 0).

Update: Erm, anonomonk protestations to the contrary aside, either order works as I said.

$ perl -e 0 -MThroatwarbler::Mangrove
Can't locate Throatwarbler/Mangrove.pm in @INC (@INC contains: /opt/lo
+cal/lib/perl5/site_perl/5.8.9/darwin-2level /opt/local/lib/perl5/site
+_perl/5.8.9 /opt/local/lib/perl5/site_perl /opt/local/lib/perl5/vendo
+r_perl/5.8.9/darwin-2level /opt/local/lib/perl5/vendor_perl/5.8.9 /op
+t/local/lib/perl5/vendor_perl/5.8.8 /opt/local/lib/perl5/vendor_perl/
+5.8.8/darwin-2level /opt/local/lib/perl5/vendor_perl /opt/local/lib/p
+erl5/5.8.9/darwin-2level /opt/local/lib/perl5/5.8.9 .).
BEGIN failed--compilation aborted.
$ perl -MThroatwarbler::Mangrove  -e 0
Can't locate Throatwarbler/Mangrove.pm in @INC (@INC contains: /opt/lo
+cal/lib/perl5/site_perl/5.8.9/darwin-2level /opt/local/lib/perl5/site
+_perl/5.8.9 /opt/local/lib/perl5/site_perl /opt/local/lib/perl5/vendo
+r_perl/5.8.9/darwin-2level /opt/local/lib/perl5/vendor_perl/5.8.9 /op
+t/local/lib/perl5/vendor_perl/5.8.8 /opt/local/lib/perl5/vendor_perl/
+5.8.8/darwin-2level /opt/local/lib/perl5/vendor_perl /opt/local/lib/p
+erl5/5.8.9/darwin-2level /opt/local/lib/perl5/5.8.9 .).
BEGIN failed--compilation aborted.
$ perl -v

This is perl, v5.8.9 built for darwin-2level

Copyright 1987-2008, Larry Wall

Perl may be copied only under the terms of either the Artistic License
+ or the
GNU General Public License, which may be found in the Perl 5 source ki
+t.

Complete documentation for Perl, including FAQ lists, should be found 
+on
this system using "man perl" or "perldoc perl".  If you have access to
+ the
Internet, point your browser at http://www.perl.org/, the Perl Home Pa
+ge.

$ perl5.10.0 -MThroatwarbler::Mangrove -e 0
Can't locate Throatwarbler/Mangrove.pm in @INC (@INC contains: /usr/lo
+cal/lib/perl5/5.10.0/darwin-2level /usr/local/lib/perl5/5.10.0 /usr/l
+ocal/lib/perl5/site_perl/5.10.0/darwin-2level /usr/local/lib/perl5/si
+te_perl/5.10.0 .).
BEGIN failed--compilation aborted.
$ perl5.10.0 -e 0 -MThroatwarbler::Mangrove
Can't locate Throatwarbler/Mangrove.pm in @INC (@INC contains: /usr/lo
+cal/lib/perl5/5.10.0/darwin-2level /usr/local/lib/perl5/5.10.0 /usr/l
+ocal/lib/perl5/site_perl/5.10.0/darwin-2level /usr/local/lib/perl5/si
+te_perl/5.10.0 .).
BEGIN failed--compilation aborted.
$ perl5.10.0 -e 0 -MCGI
$ perl5.10.0 -MCGI -e 0
$
[download]

---

---

Posts are HTML formatted. Put <p> </p> tags around your paragraphs. Put <code> </code> tags around your code and data!

Titles consisting of a single word are discouraged, and in most cases are disallowed outright.

Read Where should I post X? if you're not absolutely sure you're posting in the right place.

Please read these before you post! —

• How do I compose an effective node title?
• How do I post a question effectively?
• Markup in the Monastery

Posts may use any of the Perl Monks Approved HTML tags:

a, abbr, b, big, blockquote, br, caption, center, col, colgroup, dd, del, details, div, dl, dt, em, font, h1, h2, h3, h4, h5, h6, hr, i, ins, li, ol, p, pre, readmore, small, span, spoiler, strike, strong, sub, summary, sup, table, tbody, td, tfoot, th, thead, tr, tt, u, ul, wbr

You may need to use entities for some characters, as follows. (Exception: Within code tags, you can put the characters literally.)

	For:		Use:
	&		&
	<		&lt;
	>		&gt;
	[		&#91;
	]		&#93;

Link using PerlMonks shortcuts! What shortcuts can I use for linking?

See Writeup Formatting Tips and other pages linked from there for more info.