The MAX3140 datasheet description of 9bit mode:

The MAX3140 supports a common multidrop communication  technique  refe
+rred  to  as  9-bit  mode.  In  this mode,  the  parity  bit  is  set
+  to  indicate  a  message  that  contains  a  header  with  a  desti
+nation  address.  Set  the MAX3140’s  parity  mask  to  generate  int
+errupts  for  this condition.  Operating  a  network  in  this  mode 
+ reduces the  processing  overhead  of  all  nodes  by  enabling  the
+ slave  controllers  to  ignore  most  message  traffic.  This reliev
+es  the  remote  processor  to  handle  more  useful tasks.In  9-bit 
+ mode,  the  MAX3140  is  set  up  with  eight  bits plus  parity.  T
+he  parity  bit  in  all  normal  messages  is clear,  but  is  set  
+in  an  address-type  message.  The MAX3140’s parity-interrupt mask g
+enerates an interrupton  high  parity  when  enabled.  When  the  mas
+ter  sends an address message with the parity bit set, all MAX3140  n
+odes  issue  an  interrupt.  All  nodes  then retrieve the received b
+yte to compare to their assigned address.  Once  addressed,  the  nod
+e  continues  to process each received byte. If the node was not addr
+essed,  it  ignores  all  message  traffic  until  a  new address is 
+sent out by the master.The parity/9th-bit interrupt is controlled onl
+y by the data in the receive register and is not affected by data in 
+the FIFO,  so  the  most  effective  use  of  the  parity/9th-bitinte
+rrupt is with FIFO disabled. With the FIFO disabled, received  non-ad
+dress  words  are  ignored  and  not  even read from the UART.

[download]

The parity bit that this is referring to is a bit in an on-chip transmit control register. This register has to be modified to cause the chip generated parity bit to be set to indicate an address byte. And then be modified again to turn off address-mode.

My guess is the Device::SerialPort module doesn't use it's parity argument for this purpose.

James

There's never enough time to do it right, but always enough time to do it over...

In reply to Re^5: How to read serial port with WIN32:SerialPort? by jmlynesjr
in thread How to read serial port with WIN32:SerialPort? by mastertone

Title:
Use:  <p> text here (a paragraph) </p>
and:  <code> code here </code>
to format your post, it's "PerlMonks-approved HTML":


  • Posts are HTML formatted. Put <p> </p> tags around your paragraphs. Put <code> </code> tags around your code and data!
  • Titles consisting of a single word are discouraged, and in most cases are disallowed outright.
  • Read Where should I post X? if you're not absolutely sure you're posting in the right place.
  • Please read these before you post! —
  • Posts may use any of the Perl Monks Approved HTML tags:
    a, abbr, b, big, blockquote, br, caption, center, col, colgroup, dd, del, details, div, dl, dt, em, font, h1, h2, h3, h4, h5, h6, hr, i, ins, li, ol, p, pre, readmore, small, span, spoiler, strike, strong, sub, summary, sup, table, tbody, td, tfoot, th, thead, tr, tt, u, ul, wbr
  • You may need to use entities for some characters, as follows. (Exception: Within code tags, you can put the characters literally.)
            For:     Use:
    & &amp;
    < &lt;
    > &gt;
    [ &#91;
    ] &#93;
  • Link using PerlMonks shortcuts! What shortcuts can I use for linking?
  • See Writeup Formatting Tips and other pages linked from there for more info.